PANASONIC PT-RZ21K (3-Chip DLP / 20,000 lm / WUXGA)

Panasonic Projector: 3-Chip DLP Projector PT-RZ21K Series Introduction

Detailed Specifications

Brightness (ANSI lumens) : 20,000 ANSI

Contrast : 20,000:1

Resolution : 1920 x 1200 (WUXGA)

Lens Ratio Ratio : 1.60-2.80:1

Projector Technology : Laser Light Source / 3 Chip DLP Display

Lamp Life : 20,000 Hours

Weight : 49 kg

Dimensions WxHxD cm : 59.8 x 27.0 x 72.5

Projector Warranty : 3 Years
Lenses sold separately.

Product Specification

Technology	Laser 3-chip DLP
Power supply	AC 200V-240V, 7.7A, 50/60Hz The light output will decrease to approximately 1/2 when using the projector with AC 100V to AC 120V [9.6A].
Power consumption	1,510 W (1,525 VA [AC200V]) (0.3 W with Standby Mode set to Eco*1, 4 W with Standby Mode set to Normal) 1,217W (Normal Mode), 972 W (Eco Mode) Operating Temperature: 25 °C (77 °F), Altitude: 700m (2,297ft), IEC627087: 2008 Broadcast contents, Picture mode: Standard, Dynamic contrast [2]
BTU value	Max 5,159 BTU
DLP™ chip \| Panel size	24.4 mm (0.96 inches) diagonal (16:10 aspect ratio)
DLP™ chip \| Display method	DLP™ chip x 3, DLP™ projection system
DLP™ chip \| Pixels	6,912,000 (1920 x 1200 x 3) pixels
Refresh Rate	120 Hz*2
LENS	Optional (no lens included with this model), powered zoom, powered focus lens
Light source	Laser Diode (Laser class: Class 1)*Class 3R for North America.
Illumination life of set	Varies depending on operation mode setting. 20,000 hours at half luminance (Normal) 24,000 hours at half luminance (Eco) * IEC62087: 2008 Broadcast contents, Dynamic contrast [3] (NORMAL/ECO Temperature: 30°C (86°F), Altitude 700m (2,297 ft),Dynamic Contrast [3] Under conditions of 0.15 mg/m3 of particulate matter
Screen Size (Diagonal)	1.78-25.4 m (70-1,000 in) with 16:10 aspect ratio 1.78-15.24 m (70-600 in) with the ET-D75LE8, 16:10 aspect ratio 3.05-15.24 m (120-600 in) with the ET-D75LE95, 16:10 aspect ratio
Brightness	21,000 lm (Center)35 / 20,000 lm (Normal)45
Center-to-corner uniformity	90%
Contrast*3	20,000:1 (Full On/Full Off, Dynamic Contrast Mode: 3)
Resolution	1920 x 1200 pixels
Scanning frequency \| Video/Y/C	fH:15.73KHz fV:59.94Hz, fH:15.63KHz fV:50Hz
Scanning frequency \| RGB	・Resolution: 640 x 400 pixels to 1920 x 1200 pixels ・Dot clock frequency: 162MHz or less ・PIAS (Panasonic Intelligent Auto Scanning)
Scanning frequency \| YPBPR(YCBCR)	・Resolution: 480i/576i to 1920 x 1080 pixels ・Dot clock frequency: 148.5MHz or less ・The SYNC/HD and VD terminals do not support 3 value SYNC.
Scanning frequency \| DVI	・Moving image signal resolution: 480i6/576i6 to 1920x1080 ・Still image signal resolution: 640 x 400 to 1920 x 1200 (non-interlace) ・Dot clock frequency: 25 MHz to 162 MHz
Scanning frequency \| HDMI/DIGITAL LINK	・Moving image signal resolution: 480i6/576i6 to 1920x1080 　Still image signal resolution: 640 x 400 to 1920 x 1200 (non-interlace) ・Dot clock frequency: 25 MHz to 162 MHz
Scanning frequency \| SDI	SD-SDI signal HD-SDI signal 3G-SDI signal
Optical axis shift	Vertical (from center of screen) ±55 % (±44 % with ET-D75LE6, +68 % - +78 % with ET-D75LE95) (powered) Horizontal (from center of screen) ±20 % (±15 % with ET-D75LE6, ±12 % with ET-D75LE95) (powered) NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50.
Installation	Ceiling/floor, front /rear, free 360-degree installation
Terminals \| RGB 1 IN	BNC x 5
Terminals \| RGB 1 IN \| R, G, B	R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms HD, VD/SYNC: TTL, high impedance, positive/negative automatic
Terminals \| RGB 1 IN \| Y, PB, PR (Y, CB, CR)	Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms
Terminals \| RGB 1 IN \| Y/C	Y: 1.0 Vp-p (including sync signal), C: 0.286 Vp-p, 75 ohms
Terminals \| RGB 1 IN \| Video in	BNC x 1, 1.0 Vp-p, 75 ohms
Terminals \| RGB 2 IN	D-sub HD 15-pin (female) x 1
Terminals \| RGB 2 IN \| R, G, B	R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms HD, VD/SYNC: TTL, high impedance, positive/negative automatic
Terminals \| RGB 2 IN \| Y, PB, PR (Y, CB, CR)	Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms
Terminals \| DVI-D IN	DVI-D 24-pin x1 Single link, DVI 1.0 compliant, HDCP compatible
Terminals \| HDMI IN	HDMI 19-pin x1 HDCP compatible, Deep Color compatible
Terminals \| SDI IN 1	BNC x 1 SD-SDI signal SMPTE ST 259 compliant HD-SDI signal SMPTE ST 292 compliant 3G-SDI signal SMPTE ST 424, 425-2 compliant Dual link HD-SDI (LINK A) signal SMPTE ST 372 compliant Dual link 3G-SDI (Link 1) signal SMPTE ST 425-3 compliant
Terminals \| SDI IN 2	BNC x 1 SD-SDI signal SMPTE ST 259 compliant HD-SDI signal SMPTE ST 292 compliant 3G-SDI signal SMPTE ST 424, 425-2 compliant Dual link HD-SDI (LINK B) signal SMPTE ST 372 compliant Dual link 3G-SDI (Link 2) signal SMPTE ST 425-3 compliant
Terminals \| DIGITAL LINK	RJ-45 HDBaseT™ compliant, HDCP compatible, Deep Color compatible
Terminals \| 3D Sync 1 In/Out / Multi Projector Sync In	BNC x 1, IN : TTL Hi-z OUT : TTL max10mA
Terminals \| 3D Sync 2 Out/Multi Projector Sync Out	BNC x 1, TTL max10mA
Terminals \| SERIAL IN	D-sub 9-pin x 1 for external control (RS-232C compliant)
Terminals \| SERIAL OUT	D-sub 9-pin x 1 for link control
Terminals \| Remoter 1 In	M3 jack x 1 for wired remote control
Terminals \| Remoter 1 Out	M3 jack x 1 for link control
Terminals \| Remoter 2 In	D-sub 9-pin x 1 for external control (parallel)
Terminals \| DIGITAL LINK/LAN	RJ-45 x 1 for network connection, 100Base-TX PJLink™ (class 2) compatible, Art-Net compatible
Terminals \| DC OUT 5V	USB connector (type A) x 2 for power supply only (DC 5V, Max 2A)
Power cord length	3.0 m(9 ft 10 in)
Cabinet materials	Molded plastic
Dimensions (W x H x D)	598 x 270 x 725 mm (23 17/32inch x 10 5/8inch x 28 17/32inch ) (not including protruding parts)
Weight	*9 Approximately 49kg (108 lbs) (not including lens)
Operation noise	*3 46dB
Operating environment	Operating temperature: 0-50 °C (32-122 °F)*10; Operating humidity: 10-80 % (no condensation)
Note	1 When Standby Mode is set to ECO, network functions such as power on over LAN will not operate. Additionally, only certain c ommands can be received for external control using the serial terminal. 2 Refresh rate varies depending on scanning frequency. 3 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards. 4 The value of the light output at the center region of the projected image is extracted based on the light output measurement method de・ed by the ISO/IEC 21118:2012 international standards. 5 In AC200V, When using a projection lens other than ET-D75LE95. 6 Pixel-Repetition signal(dot clock frequency 27.0MHz) only 7 Only the vertical keystone correction angle can be corrected in the direction in which the projector body moves away from t he screen. 8 When [VERTICAL KEYSTONE] and [HORIZONTAL KEYSTONE] are used simultaneously, correction cannot be made exceeding total of 55 °. 9 Average value. May differ depending on the actual unit 10 Operating temperature is 0–45 °C (32–113 °F) when used in locations from 1,400 m to 4,200 m (4,593 ft to 13,779 ft) above sea level. When the [PROJECTOR SETUP] menu -> [OPERATION SETTING] -> [OPERATING MODE] is set to [NORMAL], and the operating environmen temperature exceeds the following value, the light output may be reduced to protect the projector. •When using the projector at an altitude lower than 2,700m (8,858') above sea level: 35°C (95°F) •When using the projector at an altitude between 2,700m (8,858') and 4,200m (13,780') above sea level: 25°C (77°F)

แบรนด์	Panasonic
dimension	598 x 270 x 725 mm.
Brightness	20000 ANSI lumens
Contrast Ratio	20,000:1
Keystone Adjustment	Vertical: ±40° (± 22° with ET-D75LE50, ±28° with ET-D75LE6), Horizontal: ±15°
Resolution Support	1920 x 1200 (WUXGA)

PANASONIC PT-RZ21K (3-Chip DLP / 20,000 lm / WUXGA)

Panasonic Projector: 3-Chip DLP Projector PT-RZ21K Series Introduction

Detailed Specifications

Product Specification

บริการของเรา

เกี่ยวกับเรา

บริการลูกค้า

ช่องทางการชำระเงิน

ติดตามเรา